After the instalation of Garuda KDE Dr460nized i cant boot the OS

[Saltybee]

Guys, i just installed Garuda Linux but when i try to boot the OS it dosent work. It apears a messages that it try every metod of booting and when i go to the BIOS its dosent appear a option to initialize in Garuda OS, just in the pendrive. Can any one help me?

[SGS]

Welcome

Seems we need more details.

How you install which DE?
Post the full ISO name and where you dwnload them.
Best way to install is to use Ventoy.net or Garuda Downloader.

• Boot the PC and press the manufacturer specific key to open your device's setup utility. Common keys used: Esc, Delete, F1, F2, F9, F10, F11, or F12. Find more common keys and buttons.
• Disable fastboot and secure boot. It may not be possible to disable the latter explicitly - try clearing the secure boot keys instead. Check the manual of your device/motherboard for further info.
• Make sure that your device's SATA controller is set to AHCI mode in your device's setup utility. Otherwise, the Linux kernel may not be able to detect your drive.
• If your firmware supports UEFI then configure your device to use UEFI only in its setup utility. UEFI is much preferred over BIOS whenever possible.
• Create a bootable USB using Garuda Downloader or (DD/Etcher/Ventoy/Rufus).
• From the setup utility, boot to the usb drive:
  You might see separate commands for the same device. For example, you might see UEFI USB Drive and BIOS USB drive. Each command uses the same device and media but boots the PC in a different firmware mode. We recommend to boot the drive in UEFI mode if listed.
• After booting the live media, start the installer and follow the guided installation procedure.

[Saltybee]

The OS that i have tryed to install is Garuda KDE Dr460nized, at first i try to download by torrent. Afther that i tyed by using Garuda Intallator. I have desable every think and follow the instalation step by step as i say in the website. Everytinks go fine until the end of the instalation, afther i reset the computer it goes again to the USB media and if a remove it it apear a message saying " all boot options are tried.".

When i tryed to re-install it it seems that is installed, but the BIOS dosent show it as an option to initialize with

[FGD]

Are you dual-booting with Windows or another OS or it is ONLY that one installation of Garuda?

[Saltybee]

Is only that, i delete windows for Garuda

[FGD]

Did you follow SGS's steps in his post above?

[SGS]

@Saltybee

afther i reset the computer it goes again to the USB media and if a remove it it apear a message saying " all boot options are tried.".

Seems you install grub on the USB-Stick.

[Saltybee]

I have tryed to install Grub but it seem unsucess, do you have a tutorial or sometink like that?

[SGS]

How to chroot Garuda Linux

From Grub fails after update - #3 by librewish Some unlucky times that your system is not bootable and the only advised option is to use chroot from a Live ISO to repair the installed system (for example, to (re)install the bootloader), here is the suggested method: steps required to chroot to your installed Garuda installation (btrfs) Boot to a Garuda usb Live ISO Start a terminal and Find your installed system (btrfs) partition, you need the /dev/<something> part. lsblk -f Warning: Remem…

Or just install again and do not use the stick as boot partition.

[BluishHumility]

@Saltybee can you confirm you have booted to the BIOS menu and reviewed the options there? You may need to explicitly enable booting from the target device.

Also disabling secure boot is not optional.

Please respond to these bullet points:

@SGS

• Disable fastboot and secure boot. It may not be possible to disable the latter explicitly - try clearing the secure boot keys instead. Check the manual of your device/motherboard for further info.
• Make sure that your device's SATA controller is set to AHCI mode in your device's setup utility. Otherwise, the Linux kernel may not be able to detect your drive.
• If your firmware supports UEFI then configure your device to use UEFI only in its setup utility. UEFI is much preferred over BIOS whenever possible.

[Saltybee]

Look, i have tryed to install grub using chroot and it gave me this error

[[email protected] /]# grub-install --target=x86_64-efi --efi-directory=/boot/efi --bootloader-id=garuda --recheck
update-grub
Installing for x86_64-efi platform.
EFI variables are not supported on this system.
EFI variables are not supported on this system.
grub-install: error: efibootmgr failed to register the boot entry: No such file or directory.
Generating grub configuration file ...
Found theme: /usr/share/grub/themes/garuda-dr460nized/theme.txt
Found linux image: /boot/vmlinuz-linux-zen
Found initrd image: /boot/intel-ucode.img /boot/initramfs-linux-zen.img
Found fallback initrd image(s) in /boot:  intel-ucode.img initramfs-linux-zen-fallback.img
fgrep: warning: fgrep is obsolescent; using grep -F
Warning: os-prober will be executed to detect other bootable partitions.
Its output will be used to detect bootable binaries on them and create new boot entries.
grub-probe: error: cannot find a GRUB drive for /dev/sdb1.  Check your device.map.
grub-probe: error: cannot find a GRUB drive for /dev/sdb1.  Check your device.map.
Detecting snapshots ...
No snapshots found.
If you think an error has occurred , please file a bug report at " https://github.com/Antynea/grub-btrfs "
Unmount /tmp/grub-btrfs.fH3RZTkp1c .. Success
Found memtest86+ image: /boot/memtest86+/memtest.bin
done

[FGD]

What did you do before issuing the command?

What error, if any, did you get when you clicked on INSTALL GARUDA LINUX from the gui window inside Garuda after booting with the USB stick?
Did you choose the option to ERASE entire disk when installing?
What is that /dev/sdb disk, is it the USB stick or a real drive?
Did you mount the EFI partition before sending that command?

[Saltybee]

Guys, the problem was in the machine i was in stalling it, i chage the computer and it work. Thanks you guys so much.