If they’re that gullible, tell them to back off or poof! you’ll make them “disappear” then see how they react.
Please take hidden videos to share with us! 
Welcome to Linux!
1 Like
Well, I am unfortunately back. At the risk of alienating @nepti , I’m wondering if I may have missed something basic in driver installation? When I look at the drivers through the Settings Manager, it tells me both video-nvidia-dkms and video-linux are installed. I’ve been trying to look around, and it seems like the open source drivers sometimes cause issues if I’m understanding right (probably not)? Should I be uninstalling video-linux?
Another thing - I have an instinct, but it’s kind of hard to prove, that video (including games) somehow is increasing the chances of crash. This session went a while without any crash, but I barely do stuff on it rn. I had doomscrolled plenty of sites with video autoplay on, but when I opened up a video to watch, it crashed within ten minutes. I know some of the other crashes are unrelated to video, but I have a feeling the probability increases when there’s a “streaming image” being run (for lack of a better term).
That’s all fine.
-
At the very beginning you installed the Nvidia card, but didn’t install any Nvidia drivers and only used the iGPU ← was the system stable?
-
Then you installed the nvidia drivers and used the nvidia card ← that’s where the problems started, right?
-
Then you used the iGPU again (the card and nvidia drivers were still installed), the issues still remained but there was no longer a black screen, right?
-
Then you used the Nvidia card again and the issues still occur today, right?
Yes (first integrated only, even though the Nvidia card was physically installed, then dedicated and problems, problems don’t crash session if I use integrated)
One other interesting thing is that iirc, I forgot to plug the monitor into the GPU for a while after installing the drivers, so the Nvidia drivers were present, but the Nvidia card wasn’t being used. I’m pretty sure I didn’t have any issues then. They only started once I plugged in the monitor. idk if that helps with anything.
Ok.
Error log from your old topic with the same issues:
Sep 26 13:47:44 beefy kernel: NVRM: Xid (PCI:0000:01:00): 79, pid='<unknown>', name=<unknown>, GPU has fallen off the bus.
Sep 26 13:47:44 beefy kernel: NVRM: GPU 0000:01:00.0: GPU has fallen off the bus.
Sep 26 13:47:44 beefy kernel: NVRM: A GPU crash dump has been created. If possible, please run
NVRM: nvidia-bug-report.sh as root to collect this data before
NVRM: the NVIDIA kernel module is unloaded.
Sep 26 13:47:44 beefy kernel: NVRM: GPU 0000:01:00.0: Failed to copy vbios to system memory.
Sep 26 13:47:44 beefy kernel: NVRM: GPU 0000:01:00.0: RmInitAdapter failed! (0x30:0xffff:976)
Sep 26 13:47:44 beefy kernel: NVRM: GPU 0000:01:00.0: rm_init_adapter failed, device minor number 0
Sep 26 13:47:44 beefy kernel: NVRM: GPU 0000:01:00.0: request_irq() failed (-22)
Sep 26 13:47:44 beefy kernel: NVRM: GPU 0000:01:00.0: request_irq() failed (-22)
Sep 26 13:47:44 beefy kernel: NVRM: GPU 0000:01:00.0: request_irq() failed (-22)
Sep 26 13:47:44 beefy kernel: NVRM: GPU 0000:01:00.0: request_irq() failed (-22)
Sep 26 13:47:44 beefy kernel: NVRM: GPU 0000:01:00.0: request_irq() failed (-22)
Sep 26 13:47:46 beefy kernel: NVRM: GPU 0000:01:00.0: request_irq() failed (-22)
Sep 26 13:47:46 beefy kernel: NVRM: GPU 0000:01:00.0: request_irq() failed (-22)
Sep 26 13:47:46 beefy kernel: NVRM: GPU 0000:01:00.0: request_irq() failed (-22)
Sep 26 13:47:46 beefy kernel: NVRM: GPU 0000:01:00.0: request_irq() failed (-22)
Sep 26 13:47:46 beefy kernel: NVRM: GPU 0000:01:00.0: request_irq() failed (-22)
Sep 26 13:47:46 beefy kernel: NVRM: GPU 0000:01:00.0: request_irq() failed (-22)
Sep 26 13:47:48 beefy kernel: NVRM: GPU 0000:01:00.0: request_irq() failed (-22)
Sep 26 13:47:48 beefy kernel: NVRM: GPU 0000:01:00.0: request_irq() failed (-22)
Sep 26 13:47:48 beefy kernel: NVRM: GPU 0000:01:00.0: request_irq() failed (-22)
Sep 26 13:47:48 beefy kernel: NVRM: GPU 0000:01:00.0: request_irq() failed (-22)
Sep 26 13:47:48 beefy kernel: NVRM: GPU 0000:01:00.0: request_irq() failed (-22)
Sep 26 13:47:48 beefy kernel: NVRM: GPU 0000:01:00.0: request_irq() failed (-22)
Xid 79 points to driver or hardware problem.
0000:01:00.0 VGA compatible controller [0300]: NVIDIA Corporation AD104 [GeForce RTX 4070 Ti] [10de:2782] (rev a1) (prog-if 00 [VGA controller])
Subsystem: Gigabyte Technology Co., Ltd AD104 [GeForce RTX 4070 Ti] [1458:40ff]
!!! Unknown header type 7f
Interrupt: pin ? routed to IRQ 205
What bothers me the most is that pin has no value (A) and just a “?” outputs.
To check if the PCIe 5.0 x16 slot is dirty or broken:
Turn off your computer and disconnect the system power cord from the power supply. Insert the graphics card into the PCIe 4.0 x16 slot at the bottom. Turn the computer back on, boot garuda and post the output from:
lspci -vv
Leave the card in the slot until the issues occur again.
As soon as the problems occur again, post the full nvidia-bug-report if possible (or journalctl).
2 Likes
Isn’t the solution in post 8?
If not, please remove the check mark.
1 Like
ok, more TIL stuff, and a bit more backstory. Some time after the problem showed up, a coworker thought it might be that the GPU wasn’t plugged into the power supply well, I opened up the machine and checked it, and seeing that there was also a 16-pin plug on the bottom, I plugged it in there for good measure (in case the top one was somehow damaged) - I hadn’t realized there was a difference between them. As a result, I’ve been on the 4.0 since then. I don’t know if you’d still specifically want the lspci -vv, but just in case, I’m attaching a link to the full readout (too long to post) and pasting what I suspect is the most relevant part here:
01:00.0 VGA compatible controller: NVIDIA Corporation AD104 [GeForce RTX 4070 Ti] (rev a1) (prog-if 00 [VGA controller])
Subsystem: Gigabyte Technology Co., Ltd Device 40ff
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 188
Region 0: Memory at 84000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at 4000000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at 4010000000 (64-bit, prefetchable) [size=32M]
Region 5: I/O ports at 6000 [size=128]
Expansion ROM at 85000000 [virtual] [disabled] [size=512K]
Capabilities: [60] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee00b18 Data: 0000
Capabilities: [78] Express (v2) Legacy Endpoint, IntMsgNum 0
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ TEE-IO-
DevCtl: CorrErr+ NonFatalErr+ FatalErr+ UnsupReq+
RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+ FLReset-
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 16GT/s, Width x16, ASPM L1, Exit Latency L1 <16us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes, LnkDisable- CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (downgraded), Width x16
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range AB, TimeoutDis+ NROPrPrP- LTR+
10BitTagComp+ 10BitTagReq+ OBFF Via message, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
AtomicOpsCtl: ReqEn-
IDOReq- IDOCompl- LTR+ EmergencyPowerReductionReq-
10BitTagReq- OBFF Disabled, EETLPPrefixBlk-
LnkCap2: Supported Link Speeds: 2.5-16GT/s, Crosslink- Retimer+ 2Retimers+ DRS-
LnkCtl2: Target Link Speed: 16GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance Preset/De-emphasis: -6dB de-emphasis, 0dB preshoot
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete+ EqualizationPhase1+
EqualizationPhase2+ EqualizationPhase3+ LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [b4] Vendor Specific Information: Len=14 <?>
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [250 v1] Latency Tolerance Reporting
Max snoop latency: 34326183936ns
Max no snoop latency: 34326183936ns
Capabilities: [258 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2- ASPM_L1.1+ L1_PM_Substates+
PortCommonModeRestoreTime=255us PortTPowerOnTime=10us
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
T_CommonMode=0us
L1SubCtl2: T_PwrOn=10us
Capabilities: [128 v1] Power Budgeting <?>
Capabilities: [420 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap- ECRCGenEn- ECRCChkCap- ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [600 v1] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?>
Capabilities: [900 v1] Secondary PCI Express
LnkCtl3: LnkEquIntrruptEn- PerformEqu-
LaneErrStat: 0
Capabilities: [bb0 v1] Physical Resizable BAR
BAR 0: current size: 16MB, supported: 16MB
BAR 1: current size: 256MB, supported: 64MB 128MB 256MB 512MB 1GB 2GB 4GB 8GB 16GB
BAR 3: current size: 32MB, supported: 32MB
Capabilities: [c1c v1] Physical Layer 16.0 GT/s <?>
Capabilities: [d00 v1] Lane Margining at the Receiver
PortCap: Uses Driver+
PortSta: MargReady- MargSoftReady-
Capabilities: [e00 v1] Data Link Feature <?>
Kernel driver in use: nvidia
Kernel modules: nouveau, nvidia_drm, nvidia
lmk if I should try switching it back to the 5.0. Either way, I’ll see if I can generate the full bug report on next crash, or use journalctl otherwise.
Thanks!
That looks better @ nvidia card.
Leave the card in the PCIe 4.0 x16 and see if the issues reoccur.
I noticed something else in the old lspci that matches the current one - that’s why I wanted the full output. But at first it’s just a suspicion.
Is the computer self-made?
2 Likes
It wasn’t a package - the store I bought from lets you pick parts and they build it, I suspect that means yes for these purposes.
ok, I managed to get ssh up, and ran a game that recently has consistently triggered the issue (it didn’t before)
link to nvidia-bug-report:
journalctl:
kernel: pcieport 0000:00:01.0: AER: Multiple Correctable error message received from 0000:00:01.0
kernel: pcieport 0000:00:01.0: PCIe Bus Error: severity=Correctable, type=Physical Layer, (Receiver ID)
kernel: pcieport 0000:00:01.0: device [8086:a70d] error status/mask=00002001/00002000
kernel: pcieport 0000:00:01.0: [ 0] RxErr (First)
kernel: NVRM: GPU at PCI:0000:01:00: GPU-f8b4909a-3ab9-4a52-2559-91139f30846c
kernel: NVRM: Xid (PCI:0000:01:00): 79, pid='<unknown>', name=<unknown>, GPU has fallen off the bus.
kernel: NVRM: GPU 0000:01:00.0: GPU has fallen off the bus.
sudo[1571860]: x : a password is required ; TTY=pts/1 ; PWD=/home/x ; USER=root ; COMMAND=/usr/bin/true
01 kernel: nvidia-modeset: ERROR: GPU:0: Failed to query display engine channel state: 0x0000c67e:6:0:0x0000000f
03 sudo[1571892]: x : a password is required ; TTY=pts/1 ; PWD=/home/x ; USER=root ; COMMAND=/usr/bin/true
06 plasmashell[1067797]: [GFX1]: Device reset due to WR context
06 plasmashell[1067797]: [GFX1-]: GFX: RenderThread detected a device reset in PostUpdate
06 kernel: nvidia-modeset: ERROR: GPU:0: Failed to query display engine channel state: 0x0000c67e:6:0:0x0000000f
06 kernel: nvidia-modeset: ERROR: GPU:0: Failed to query display engine channel state: 0x0000c67e:6:0:0x0000000f
06 kernel: nvidia-modeset: ERROR: GPU:0: Failed to query display engine channel state: 0x0000c67e:6:0:0x0000000f
06 kernel: nvidia-modeset: ERROR: GPU:0: Failed to query display engine channel state: 0x0000c67e:6:0:0x0000000f
06 kernel: nvidia-modeset: ERROR: GPU:0: Failed to query display engine channel state: 0x0000c67e:6:0:0x0000000f
06 kernel: nvidia-modeset: ERROR: GPU:0: Failed to query display engine channel state: 0x0000c67e:6:0:0x0000000f
06 kernel: nvidia-modeset: ERROR: GPU:0: Failed to query display engine channel state: 0x0000c67e:6:0:0x0000000f
06 plasmashell[1067797]: ExceptionHandler::GenerateDump cloned child 1571918
06 plasmashell[1067797]: ExceptionHandler::SendContinueSignalToChild sent continue signal to child
06 plasmashell[1571918]: ExceptionHandler::WaitForContinueSignal waiting for continue signal...
07 kernel: nvidia-modeset: ERROR: GPU:0: Failed to query display engine channel state: 0x0000c67e:6:0:0x0000000f
07 plasmashell[1402320]: Exiting due to channel error.
07 plasmashell[1404383]: Exiting due to channel error.
07 plasmashell[1184067]: Exiting due to channel error.
07 plasmashell[1404424]: Exiting due to channel error.
07 plasmashell[1203284]: Exiting due to channel error.
07 plasmashell[1361962]: Exiting due to channel error.
07 plasmashell[1283634]: Exiting due to channel error.
07 plasmashell[1251182]: Exiting due to channel error.
07 plasmashell[1150582]: Exiting due to channel error.
07 plasmashell[1068138]: Exiting due to channel error.
07 plasmashell[1184014]: Exiting due to channel error.
07 plasmashell[1207130]: Exiting due to channel error.
07 plasmashell[1150621]: Exiting due to channel error.
07 plasmashell[1266450]: Exiting due to channel error.
07 plasmashell[1543038]: Exiting due to channel error.
07 plasmashell[1243487]: Exiting due to channel error.
07 plasmashell[1144470]: Exiting due to channel error.
07 plasmashell[1183956]: Exiting due to channel error.
07 plasmashell[1279713]: Exiting due to channel error.
07 kernel: nvidia-modeset: ERROR: GPU:0: Failed to query display engine channel state: 0x0000c67e:6:0:0x0000000f
07 kernel: nvidia-modeset: ERROR: GPU:0: Failed to query display engine channel state: 0x0000c67e:6:0:0x0000000f
07 kernel: nvidia-modeset: ERROR: GPU:0: Failed to query display engine channel state: 0x0000c67e:6:0:0x0000000f
07 kernel: nvidia-modeset: ERROR: GPU:0: Failed to query display engine channel state: 0x0000c67e:6:0:0x0000000f
07 plasmashell[1068047]: Exiting due to channel error.
07 plasmashell[1112278]: Exiting due to channel error.
07 plasmashell[1067962]: Exiting due to channel error.
07 plasmashell[1068039]: Exiting due to channel error.
07 plasmashell[1067904]: Exiting due to channel error.
07 plasmashell[1144520]: Exiting due to channel error.
07 plasmashell[1068040]: Exiting due to channel error.
07 plasmashell[1068221]: Exiting due to channel error.
07 kernel: nvidia-modeset: ERROR: GPU:0: Failed to query display engine channel state: 0x0000c67e:6:0:0x0000000f
10 sudo[1571907]: x : TTY=pts/1 ; PWD=/home/x ; USER=root ; COMMAND=/usr/bin/nvidia-bug-report.sh
10 sudo[1571907]: pam_unix(sudo:session): session opened for user root(uid=0) by x(uid=1000)
16 kernel: snd_hda_codec_hdmi hdaudioC2D0: HDMI: invalid ELD buf size -1
16 sudo[1571907]: pam_unix(sudo:session): session closed for user root
16 sudo[1574918]: x : TTY=pts/1 ; PWD=/home/x ; USER=root ; COMMAND=/usr/bin/true
16 sudo[1574918]: pam_unix(sudo:session): session opened for user root(uid=0) by x(uid=1000)
The same error occurs in both slots: PCI bridge / PCI Express root port. Since the 5.0 depends on the CPU and the 4.0 on the chipset, the mobo should be fine.
The question is whether the card triggers this or the driver.
Put the card back into the 5.0 slot, remove the nvidia driver and install the nouveau driver to test.
Edit: The same game with the nouveau driver: post the output from
lspci -vv
In case of a crash: journalctl + lspci -vv.
Edit 2: The error is always the same from the start, the PCI bridge has a problem and kicks out the graphics card (journalctl/dmesg).
In all nvidia bug reports the PCI bridge is faulty and there is no indication of a driver error.
What’s interesting is that the PCI bridge wasn’t working properly even before the issues, it generally doesn’t work properly.
That’s why I wanted the full log from lspci -vv from before the crash. This is the state after booting and before the crash:
00:1a.0 PCI bridge: Intel Corporation Raptor Lake PCI Express Root Port #25 (rev 11) (prog-if 00 [Normal decode])
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin ? routed to IRQ 123
00:1c.0 PCI bridge: Intel Corporation Raptor Lake PCI Express Root Port #1 (rev 11) (prog-if 00 [Normal decode])
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin ? routed to IRQ 124
00:1d.0 PCI bridge: Intel Corporation Device 7a36 (rev 11) (prog-if 00 [Normal decode])
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin ? routed to IRQ 126
01:00.0 VGA compatible controller: NVIDIA Corporation AD104 [GeForce RTX 4070 Ti] (rev a1) (prog-if 00 [VGA controller])
Subsystem: Gigabyte Technology Co., Ltd Device 40ff
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 188
Did I understand correctly that the card was in the lower PCIex16 4.0 slot the whole time?
3 Likes
I opened up the machine to plug the GPU into the 5.0 slots, but am now a bit confused by what I’m finding in terms of the power supply’s setup. There are five 8-pin slots marked CPU/VGA/PCI-E, with three on the top and two on the bottom. When I opened up the machine, all three top slots were taken, afaict two by the CPU, and one that was plugged into the GPU. There was another 8-pin plugged into the GPU on the bottom. I suspect I only realized one of them was plugged into the GPU when I messed around with it before. I’ve now moved the two CPU 8-pins to the bottom row, and have the two GPU 8-pins next to each other on the top. I still get crashes, so I’m going to try deleting the nvidia drivers - I’ve got a question about that at the bottom.
I can’t find any documentation of there being any difference between the top and the bottom sockets, I just figured I’d raise that just in case for some reason this particular PSU is different. It’s a ROG Thor 850P, though the diagram in the manual looks different than what I’ve got (it shows three rows of sockets, there are only two on mine).
I had thought so, but discovered that half was plugged into the top row and half on the bottom, but then also can’t find any references to which are 4.0 and which 5.0 in this unit (mentioned above). At this point, both 8-pins attached to the nvidia GPU are plugged in adjacent to each other on the top row.
Just in case all of this calls for a new lspci -vv:
λ lspci -vv
00:00.0 Host bridge: Intel Corporation Device a700 (rev 01)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.0 PCI bridge: Intel Corporation Device a70d (rev 01) (prog-if 00 [Normal decode])
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 122
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 6000-6fff [size=4K] [16-bit]
Memory behind bridge: 84000000-850fffff [size=17M] [32-bit]
Prefetchable memory behind bridge: 6000000000-6011ffffff [size=288M] [32-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:02.0 VGA compatible controller: Intel Corporation Raptor Lake-S GT1 [UHD Graphics 770] (rev 04) (prog-if 00 [VGA controller])
DeviceName: Onboard IGD
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 211
Region 0: Memory at 6016000000 (64-bit, non-prefetchable) [size=16M]
Region 2: Memory at 4000000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 7000 [size=64]
Expansion ROM at 000c0000 [virtual] [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: i915
Kernel modules: i915, xe
00:06.0 PCI bridge: Intel Corporation Raptor Lake PCIe 4.0 Graphics Port (rev 01) (prog-if 00 [Normal decode])
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 123
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: [disabled] [16-bit]
Memory behind bridge: 87100000-871fffff [size=1M] [32-bit]
Prefetchable memory behind bridge: [disabled] [64-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:0a.0 Signal processing controller: Intel Corporation Raptor Lake Crashlog and Telemetry (rev 01)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at 6017210000 (64-bit, non-prefetchable) [size=32K]
Capabilities: <access denied>
Kernel driver in use: intel_vsec
Kernel modules: intel_vsec
00:0e.0 RAID bus controller: Intel Corporation Volume Management Device NVMe RAID Controller Intel Corporation
DeviceName: RAID Controller
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Region 0: Memory at 6014000000 (64-bit, non-prefetchable) [size=32M]
Region 2: Memory at 82000000 (32-bit, non-prefetchable) [size=32M]
Region 4: Memory at 6017100000 (64-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
Kernel driver in use: vmd
Kernel modules: vmd
00:14.0 USB controller: Intel Corporation Raptor Lake USB 3.2 Gen 2x2 (20 Gb/s) XHCI Host Controller (rev 11) (prog-if 30 [XHCI])
DeviceName: USB Controller
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 148
Region 0: Memory at 6017200000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
Kernel modules: mei_me, xhci_pci
00:14.2 RAM memory: Intel Corporation Raptor Lake-S PCH Shared SRAM (rev 11)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at 6017228000 (64-bit, non-prefetchable) [disabled] [size=16K]
Region 2: Memory at 6017231000 (64-bit, non-prefetchable) [disabled] [size=4K]
Capabilities: <access denied>
00:14.3 Network controller: Intel Corporation Raptor Lake-S PCH CNVi WiFi (rev 11)
Subsystem: Intel Corporation Device 0094
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at 6017224000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
00:15.0 Serial bus controller: Intel Corporation Raptor Lake Serial IO I2C Host Controller #0 (rev 11)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 27
Region 0: Memory at 4017000000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: intel-lpss
Kernel modules: intel_lpss_pci
00:15.1 Serial bus controller: Intel Corporation Raptor Lake Serial IO I2C Host Controller #1 (rev 11)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 40
Region 0: Memory at 4017001000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: intel-lpss
Kernel modules: intel_lpss_pci
00:15.2 Serial bus controller: Intel Corporation Raptor Lake Serial IO I2C Host Controller #2 (rev 11)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 29
Region 0: Memory at 4017002000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: intel-lpss
Kernel modules: intel_lpss_pci
00:16.0 Communication controller: Intel Corporation Raptor Lake CSME HECI #1 (rev 11)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 255
Region 0: Memory at 601722d000 (64-bit, non-prefetchable) [disabled] [size=4K]
Capabilities: <access denied>
Kernel modules: mei_me
00:17.0 SATA controller: Intel Corporation Raptor Lake SATA AHCI Controller (rev 11) (prog-if 01 [AHCI 1.0])
DeviceName: SATA Controller
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 128
Region 0: Memory at 87200000 (32-bit, non-prefetchable) [size=8K]
Region 1: Memory at 87203000 (32-bit, non-prefetchable) [size=256]
Region 2: I/O ports at 7090 [size=8]
Region 3: I/O ports at 7080 [size=4]
Region 4: I/O ports at 7060 [size=32]
Region 5: Memory at 87202000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1a.0 PCI bridge: Intel Corporation Raptor Lake PCI Express Root Port #25 (rev 11) (prog-if 00 [Normal decode])
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin ? routed to IRQ 124
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 5000-5fff [size=4K] [16-bit]
Memory behind bridge: 86500000-86efffff [size=10M] [32-bit]
Prefetchable memory behind bridge: 6013500000-6013efffff [size=10M] [32-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.0 PCI bridge: Intel Corporation Raptor Lake PCI Express Root Port #1 (rev 11) (prog-if 00 [Normal decode])
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin ? routed to IRQ 125
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 4000-4fff [size=4K] [16-bit]
Memory behind bridge: 85b00000-864fffff [size=10M] [32-bit]
Prefetchable memory behind bridge: 6012b00000-60134fffff [size=10M] [32-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.2 PCI bridge: Intel Corporation Device 7a3a (rev 11) (prog-if 00 [Normal decode])
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 126
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: [disabled] [16-bit]
Memory behind bridge: 86f00000-870fffff [size=2M] [32-bit]
Prefetchable memory behind bridge: [disabled] [64-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 PCI bridge: Intel Corporation Device 7a36 (rev 11) (prog-if 00 [Normal decode])
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin ? routed to IRQ 127
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
I/O behind bridge: 3000-3fff [size=4K] [16-bit]
Memory behind bridge: 85100000-85afffff [size=10M] [32-bit]
Prefetchable memory behind bridge: 6012100000-6012afffff [size=10M] [32-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1f.0 ISA bridge: Intel Corporation Device 7a06 (rev 11)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:1f.3 Audio device: Intel Corporation Raptor Lake High Definition Audio Controller (rev 11)
DeviceName: Intel HD Audio
Subsystem: ASUSTeK Computer Inc. Device 87c5
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 212
Region 0: Memory at 6017220000 (64-bit, non-prefetchable) [size=16K]
Region 4: Memory at 6017000000 (64-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel, snd_sof_pci_intel_tgl
00:1f.4 SMBus: Intel Corporation Raptor Lake-S PCH SMBus Controller (rev 11)
DeviceName: SMBus Controller
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at 601722c000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at efa0 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c_i801
00:1f.5 Serial bus controller: Intel Corporation Raptor Lake SPI (flash) Controller (rev 11)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at 80800000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: intel-spi
Kernel modules: spi_intel_pci
01:00.0 VGA compatible controller: NVIDIA Corporation AD104 [GeForce RTX 4070 Ti] (rev a1) (prog-if 00 [VGA controller])
Subsystem: Gigabyte Technology Co., Ltd Device 40ff
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 189
Region 0: Memory at 84000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at 6000000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at 6010000000 (64-bit, prefetchable) [size=32M]
Region 5: I/O ports at 6000 [size=128]
Expansion ROM at 85000000 [virtual] [disabled] [size=512K]
Capabilities: <access denied>
debug2: channel 0: window 997666 sent adjust 50910
Kernel driver in use: nvidia
Kernel modules: nouveau, nvidia_drm, nvidia
01:00.1 Audio device: NVIDIA Corporation Device 22bc (rev a1)
Subsystem: Gigabyte Technology Co., Ltd Device 40ff
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at 85080000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
02:00.0 Non-Volatile memory controller: Samsung Electronics Co Ltd NVMe SSD Controller PM9A1/PM9A3/980PRO (prog-if 02 [NVM Express])
Subsystem: Samsung Electronics Co Ltd SSD 980 PRO
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at 87100000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: nvme
Kernel modules: nvme
05:00.0 Ethernet controller: Intel Corporation Ethernet Controller I226-V (rev 06)
DeviceName: Intel I226V LAN
Subsystem: ASUSTeK Computer Inc. Device 8867
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at 86f00000 (32-bit, non-prefetchable) [size=1M]
Region 3: Memory at 87000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: igc
Kernel modules: igc
Just in case it’s relevant, I did change one other BIOS setting - I enabled having the iGPU work even when there’s a discrete graphics card. I figure I’ll need to do this to be able to delete the nvidia drivers, and it would be useful anyway.
I’m trying to uninstall the nvidia drivers, as recommended. I’m using the Settings Manager, and when I try uninstalling video-nvidia-dkms (the only proprietary nvidia driver installed), it tells me it can’t bc garuda-nvidia-rime-config needs it. I suspect I can use something like sudo mhwd --remove pci nvidia-dkms but I’d really prefer to check in before I potentially send a wrecking ball through everything.
On another note, I ran mhwd -li just bc I’d seen it run in some other thread, and it says the video-linux version is 2021.08.29, which seems quite old to me. I routinely update the system, so I would have thought I have the latest drivers? idk. Similarly, video-nvidia-prime-render-offload shows up as an option in the hardware config in the Setting Manager, but isn’t installed. Should it be? afaict it’s for dual setups with a iGPU and discrete nvidia GPU (like my setup), but I don’t want to further bork things at this point.
Looking at another thread I found, it looks like the way to get rid of video-nvidia-dkms is to first do sudo pacman -R garuda-nvidia-prime-config, I’ve done that and removed video-nvidia-dkms. I think the Nouveau drivers are video-linux? If so, I’ve got them installed already. I’ve been running on the iGPU, I’ll reboot now into the GPU.
I did get a crash eventually, I had forgotten to do lspci -vv first, but did at least do it afterwards. This one is different from previous ones, though - no fan spinning, for one. I had a recording playing, and it’s been running without problems since (over 30min, for sure). I’m even able to interact with the session. Plugging the monitor into the CPU still doesn’t give me any image (while still in the middle of the session that started on the GPU), but I think that’s expected.
Here’s the lspci from after the crash:
λ lspci -vv
00:00.0 Host bridge: Intel Corporation Device a700 (rev 01)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.0 PCI bridge: Intel Corporation Device a70d (rev 01) (prog-if 00 [Normal decode])
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 122
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 6000-6fff [size=4K] [16-bit]
Memory behind bridge: 84000000-850fffff [size=17M] [32-bit]
Prefetchable memory behind bridge: 6000000000-6011ffffff [size=288M] [32-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:02.0 VGA compatible controller: Intel Corporation Raptor Lake-S GT1 [UHD Graphics 770] (rev 04) (prog-if 00 [VGA controller])
DeviceName: Onboard IGD
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 189
Region 0: Memory at 6016000000 (64-bit, non-prefetchable) [size=16M]
Region 2: Memory at 4000000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 7000 [size=64]
Expansion ROM at 000c0000 [virtual] [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: i915
Kernel modules: i915, xe
00:06.0 PCI bridge: Intel Corporation Raptor Lake PCIe 4.0 Graphics Port (rev 01) (prog-if 00 [Normal decode])
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 123
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: [disabled] [16-bit]
Memory behind bridge: 87100000-871fffff [size=1M] [32-bit]
Prefetchable memory behind bridge: [disabled] [64-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:0a.0 Signal processing controller: Intel Corporation Raptor Lake Crashlog and Telemetry (rev 01)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at 6017210000 (64-bit, non-prefetchable) [size=32K]
Capabilities: <access denied>
Kernel driver in use: intel_vsec
Kernel modules: intel_vsec
00:0e.0 RAID bus controller: Intel Corporation Volume Management Device NVMe RAID Controller Intel Corporation
DeviceName: RAID Controller
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Region 0: Memory at 6014000000 (64-bit, non-prefetchable) [size=32M]
Region 2: Memory at 82000000 (32-bit, non-prefetchable) [size=32M]
Region 4: Memory at 6017100000 (64-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
Kernel driver in use: vmd
Kernel modules: vmd
00:14.0 USB controller: Intel Corporation Raptor Lake USB 3.2 Gen 2x2 (20 Gb/s) XHCI Host Controller (rev 11) (prog-if 30 [XHCI])
DeviceName: USB Controller
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 148
Region 0: Memory at 6017200000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
Kernel modules: mei_me, xhci_pci
00:14.2 RAM memory: Intel Corporation Raptor Lake-S PCH Shared SRAM (rev 11)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at 6017228000 (64-bit, non-prefetchable) [disabled] [size=16K]
Region 2: Memory at 6017231000 (64-bit, non-prefetchable) [disabled] [size=4K]
Capabilities: <access denied>
00:14.3 Network controller: Intel Corporation Raptor Lake-S PCH CNVi WiFi (rev 11)
Subsystem: Intel Corporation Device 0094
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at 6017224000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
00:15.0 Serial bus controller: Intel Corporation Raptor Lake Serial IO I2C Host Controller #0 (rev 11)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 27
Region 0: Memory at 4017000000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: intel-lpss
Kernel modules: intel_lpss_pci
00:15.1 Serial bus controller: Intel Corporation Raptor Lake Serial IO I2C Host Controller #1 (rev 11)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 40
Region 0: Memory at 4017001000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: intel-lpss
Kernel modules: intel_lpss_pci
00:15.2 Serial bus controller: Intel Corporation Raptor Lake Serial IO I2C Host Controller #2 (rev 11)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 29
Region 0: Memory at 4017002000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: intel-lpss
Kernel modules: intel_lpss_pci
00:16.0 Communication controller: Intel Corporation Raptor Lake CSME HECI #1 (rev 11)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 255
Region 0: Memory at 601722d000 (64-bit, non-prefetchable) [disabled] [size=4K]
Capabilities: <access denied>
Kernel modules: mei_me
00:17.0 SATA controller: Intel Corporation Raptor Lake SATA AHCI Controller (rev 11) (prog-if 01 [AHCI 1.0])
DeviceName: SATA Controller
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 128
Region 0: Memory at 87200000 (32-bit, non-prefetchable) [size=8K]
Region 1: Memory at 87203000 (32-bit, non-prefetchable) [size=256]
Region 2: I/O ports at 7090 [size=8]
Region 3: I/O ports at 7080 [size=4]
Region 4: I/O ports at 7060 [size=32]
Region 5: Memory at 87202000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1a.0 PCI bridge: Intel Corporation Raptor Lake PCI Express Root Port #25 (rev 11) (prog-if 00 [Normal decode])
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin ? routed to IRQ 124
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 5000-5fff [size=4K] [16-bit]
Memory behind bridge: 86500000-86efffff [size=10M] [32-bit]
Prefetchable memory behind bridge: 6013500000-6013efffff [size=10M] [32-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.0 PCI bridge: Intel Corporation Raptor Lake PCI Express Root Port #1 (rev 11) (prog-if 00 [Normal decode])
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin ? routed to IRQ 125
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 4000-4fff [size=4K] [16-bit]
Memory behind bridge: 85b00000-864fffff [size=10M] [32-bit]
Prefetchable memory behind bridge: 6012b00000-60134fffff [size=10M] [32-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.2 PCI bridge: Intel Corporation Device 7a3a (rev 11) (prog-if 00 [Normal decode])
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 126
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: [disabled] [16-bit]
Memory behind bridge: 86f00000-870fffff [size=2M] [32-bit]
Prefetchable memory behind bridge: [disabled] [64-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 PCI bridge: Intel Corporation Device 7a36 (rev 11) (prog-if 00 [Normal decode])
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin ? routed to IRQ 127
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
I/O behind bridge: 3000-3fff [size=4K] [16-bit]
Memory behind bridge: 85100000-85afffff [size=10M] [32-bit]
Prefetchable memory behind bridge: 6012100000-6012afffff [size=10M] [32-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1f.0 ISA bridge: Intel Corporation Device 7a06 (rev 11)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:1f.3 Audio device: Intel Corporation Raptor Lake High Definition Audio Controller (rev 11)
DeviceName: Intel HD Audio
Subsystem: ASUSTeK Computer Inc. Device 87c5
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 211
Region 0: Memory at 6017220000 (64-bit, non-prefetchable) [size=16K]
Region 4: Memory at 6017000000 (64-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel, snd_sof_pci_intel_tgl
00:1f.4 SMBus: Intel Corporation Raptor Lake-S PCH SMBus Controller (rev 11)
DeviceName: SMBus Controller
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at 601722c000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at efa0 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c_i801
00:1f.5 Serial bus controller: Intel Corporation Raptor Lake SPI (flash) Controller (rev 11)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at 80800000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: intel-spi
Kernel modules: spi_intel_pci
01:00.0 VGA compatible controller: NVIDIA Corporation AD104 [GeForce RTX 4070 Ti] (rev a1) (prog-if 00 [VGA controller])
Subsystem: Gigabyte Technology Co., Ltd Device 40ff
!!! Unknown header type 7f
Interrupt: pin ? routed to IRQ 255
Region 0: Memory at 84000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at 6000000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at 6010000000 (64-bit, prefetchable) [size=32M]
Region 5: I/O ports at 6000 [size=128]
Expansion ROM at 85000000 [disabled] [size=512K]
Kernel modules: nouveau
01:00.1 Audio device: NVIDIA Corporation Device 22bc (rev a1)
Subsystem: Gigabyte Technology Co., Ltd Device 40ff
!!! Unknown header type 7f
Interrupt: pin ? routed to IRQ 17
Region 0: Memory at 85080000 (32-bit, non-prefetchable) [size=16K]
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
02:00.0 Non-Volatile memory controller: Samsung Electronics Co Ltd NVMe SSD Controller PM9A1/PM9A3/980PRO (prog-if 02 [NVM Express])
Subsystem: Samsung Electronics Co Ltd SSD 980 PRO
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at 87100000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: nvme
Kernel modules: nvme
05:00.0 Ethernet controller: Intel Corporation Ethernet Controller I226-V (rev 06)
DeviceName: Intel I226V LAN
Subsystem: ASUSTeK Computer Inc. Device 8867
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at 86f00000 (32-bit, non-prefetchable) [size=1M]
Region 3: Memory at 87000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: igc
Kernel modules: igc
Here’s the nvidia-bug-report: Garuda's PrivateBin
You’re ruining a holiday for me 
I don’t know if I’m misunderstanding you or you’re misunderstanding me (plug vs. slot). How to connect the GPU is described in the power supply manual and in the Nvidia manual.
Slots are the two slots on the mobo, the upper one is a PCIe 5.0 x16 slot and the lower one is a PCIe 4.0 x16 slot.
The GPU goes into the top PCIe 5.0 x16 slot.
A kind of null method:
Remove the GPU from the computer and connect the monitor to the iGPU.
Turn on your computer and go to BIOS.
Disable everything that is called RAID, VMD or Intel RST (Rapid Storage Technology) - you only have one drive → Safe and Exit.
Boot Garuda and post the output again:
lspci -vv
btw: Edit your previous post if nobody has yet replied 
2 Likes
oh my, I was just out myself - please don’t feel obligated to answer while you’re out, it can wait. ofc I want my main machine to work, but you’ve already given me so much of your time, and I do have another machine to work from.
I was misunderstanding you. fwiw, it’s in the 5.0/top one (and always has been). I’ve pulled the GPU out entirely, and in BIOS I’ve disabled the VMD controller. Rapid Storage was already off, and I don’t see any other settings for RAID. (I did also find that there was something that looked like an ASPM module that was still active - native PCI power management, or something like that. I disabled that too.)
I still have weirdness in Garuda itself once booting through - wallpaper doesn’t render, menus tear/flicker, some things don’t work right.
lspci -vv:
λ lspci -vv
00:00.0 Host bridge: Intel Corporation Device a700 (rev 01)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:02.0 VGA compatible controller: Intel Corporation Raptor Lake-S GT1 [UHD Graphics 770] (rev 04) (prog-if 00 [VGA controller])
DeviceName: Onboard IGD
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 169
Region 0: Memory at 6002000000 (64-bit, non-prefetchable) [size=16M]
Region 2: Memory at 4000000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 6000 [size=64]
Expansion ROM at 000c0000 [virtual] [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: i915
Kernel modules: i915, xe
00:06.0 PCI bridge: Intel Corporation Raptor Lake PCIe 4.0 Graphics Port (rev 01) (prog-if 00 [Normal decode])
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 122
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: [disabled] [16-bit]
Memory behind bridge: 82800000-828fffff [size=1M] [32-bit]
Prefetchable memory behind bridge: [disabled] [64-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:0a.0 Signal processing controller: Intel Corporation Raptor Lake Crashlog and Telemetry (rev 01)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at 6003110000 (64-bit, non-prefetchable) [size=32K]
Capabilities: <access denied>
Kernel driver in use: intel_vsec
Kernel modules: intel_vsec
00:14.0 USB controller: Intel Corporation Raptor Lake USB 3.2 Gen 2x2 (20 Gb/s) XHCI Host Controller (rev 11) (prog-if 30 [XHCI])
DeviceName: USB Controller
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 128
Region 0: Memory at 6003100000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
Kernel modules: mei_me, xhci_pci
00:14.2 RAM memory: Intel Corporation Raptor Lake-S PCH Shared SRAM (rev 11)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at 6003128000 (64-bit, non-prefetchable) [disabled] [size=16K]
Region 2: Memory at 6003131000 (64-bit, non-prefetchable) [disabled] [size=4K]
Capabilities: <access denied>
00:14.3 Network controller: Intel Corporation Raptor Lake-S PCH CNVi WiFi (rev 11)
Subsystem: Intel Corporation Device 0094
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at 6003124000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
00:15.0 Serial bus controller: Intel Corporation Raptor Lake Serial IO I2C Host Controller #0 (rev 11)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 27
Region 0: Memory at 4017000000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: intel-lpss
Kernel modules: intel_lpss_pci
00:15.1 Serial bus controller: Intel Corporation Raptor Lake Serial IO I2C Host Controller #1 (rev 11)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 40
Region 0: Memory at 4017001000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: intel-lpss
Kernel modules: intel_lpss_pci
00:15.2 Serial bus controller: Intel Corporation Raptor Lake Serial IO I2C Host Controller #2 (rev 11)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 29
Region 0: Memory at 4017002000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: intel-lpss
Kernel modules: intel_lpss_pci
00:16.0 Communication controller: Intel Corporation Raptor Lake CSME HECI #1 (rev 11)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 255
Region 0: Memory at 600312d000 (64-bit, non-prefetchable) [disabled] [size=4K]
Capabilities: <access denied>
Kernel modules: mei_me
00:17.0 SATA controller: Intel Corporation Raptor Lake SATA AHCI Controller (rev 11) (prog-if 01 [AHCI 1.0])
DeviceName: SATA Controller
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 127
Region 0: Memory at 82900000 (32-bit, non-prefetchable) [size=8K]
Region 1: Memory at 82903000 (32-bit, non-prefetchable) [size=256]
Region 2: I/O ports at 6090 [size=8]
Region 3: I/O ports at 6080 [size=4]
Region 4: I/O ports at 6060 [size=32]
Region 5: Memory at 82902000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1a.0 PCI bridge: Intel Corporation Raptor Lake PCI Express Root Port #25 (rev 11) (prog-if 00 [Normal decode])
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin ? routed to IRQ 123
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 5000-5fff [size=4K] [16-bit]
Memory behind bridge: 81c00000-825fffff [size=10M] [32-bit]
Prefetchable memory behind bridge: 6001400000-6001dfffff [size=10M] [32-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.0 PCI bridge: Intel Corporation Raptor Lake PCI Express Root Port #1 (rev 11) (prog-if 00 [Normal decode])
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin ? routed to IRQ 124
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 4000-4fff [size=4K] [16-bit]
Memory behind bridge: 81200000-81bfffff [size=10M] [32-bit]
Prefetchable memory behind bridge: 6000a00000-60013fffff [size=10M] [32-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.2 PCI bridge: Intel Corporation Device 7a3a (rev 11) (prog-if 00 [Normal decode])
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 125
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: [disabled] [16-bit]
Memory behind bridge: 82600000-827fffff [size=2M] [32-bit]
Prefetchable memory behind bridge: [disabled] [64-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 PCI bridge: Intel Corporation Device 7a36 (rev 11) (prog-if 00 [Normal decode])
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin ? routed to IRQ 126
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 3000-3fff [size=4K] [16-bit]
Memory behind bridge: 80800000-811fffff [size=10M] [32-bit]
Prefetchable memory behind bridge: 6000000000-60009fffff [size=10M] [32-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1f.0 ISA bridge: Intel Corporation Device 7a06 (rev 11)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:1f.3 Audio device: Intel Corporation Raptor Lake High Definition Audio Controller (rev 11)
DeviceName: Intel HD Audio
Subsystem: ASUSTeK Computer Inc. Device 87c5
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 191
Region 0: Memory at 6003120000 (64-bit, non-prefetchable) [size=16K]
Region 4: Memory at 6003000000 (64-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel, snd_sof_pci_intel_tgl
00:1f.4 SMBus: Intel Corporation Raptor Lake-S PCH SMBus Controller (rev 11)
DeviceName: SMBus Controller
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at 600312c000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at efa0 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c_i801
00:1f.5 Serial bus controller: Intel Corporation Raptor Lake SPI (flash) Controller (rev 11)
Subsystem: ASUSTeK Computer Inc. Device 8882
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at 82904000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: intel-spi
Kernel modules: spi_intel_pci
01:00.0 Non-Volatile memory controller: Samsung Electronics Co Ltd NVMe SSD Controller PM9A1/PM9A3/980PRO (prog-if 02 [NVM Express])
Subsystem: Samsung Electronics Co Ltd SSD 980 PRO
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at 82800000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: nvme
Kernel modules: nvme
04:00.0 Ethernet controller: Intel Corporation Ethernet Controller I226-V (rev 06)
DeviceName: Intel I226V LAN
Subsystem: ASUSTeK Computer Inc. Device 8867
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at 82600000 (32-bit, non-prefetchable) [size=1M]
Region 3: Memory at 82700000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: igc
Kernel modules: igc
Should I be trying the GPU in the 4.0 socket in the mobo?
And again, thanks for everything so far, and don’t worry about pushing this until after the vacation.
It was just a joke
No, I wanted to know if the GPU is causing this. But she doesn’t do that:
and:
Disabling RAID/VMD/RST was intended to exclude a conflict between the PCIe NVMe controller and the resources of the PCI bus.
You have the same problem with the iGPU.
You could try resetting the BIOS and reinstalling garuda (without the RTX 4070 Ti). Only in a minimal configuration.
But at the moment I’m assuming a hardware defect.
1 Like
There is a known issue with this driver causing kernel memory corruption. This can result in crashes, hard freezes, or other issues. With kernel memory corruption, the behavior you get is somewhat unpredictable but will generally look like bad hardware.
There is a related discussion in this topic from another forum if you would like to take a look:
There don’t seem to be any super great options for dealing with this right now. You can downgrade the driver and associated packages, which may require switching kernels as well, or scrap the drivers altogether and run Nouveau for a while. Have a read through that thread and see what you think.
4 Likes
Would that mean a motherboard issue? I’m guessing the issue is the Interrupt: pin ? lines, but don’t really know what I’m looking at.
I’m mainly curious bc it would be a whole lot easier for to not need to drag the whole case in to the shop, though I certainly can if I need to.
@BluishHumility if it was the issue you mentioned, would it also explain the issues I’m having with the iGPU?
Thanks for your input @BluishHumility.
I know the problem with version 550.67 and had that in mind. The OP is now on version 550.76. But the issues occur in all scenarios and have been for a long time (version 535.113.01). With GPU and nVidia drivers, with GPU and Nouveau drivers. And now without GPU but on the iGPU. The fact that the PCI bus does not provide an interrupt pin has been true from the beginning. In the last nvidia bug report there is also a chipset error.
2 Likes